Jinling as an innovation-oriented enterprise specialized in advanced technology.We have over 20 years of experience in machine manufacturing.
Centrifugal Scraper Thin-film Evaporator
This machine uses high-speed rotation to distribute the liquid into auniform film. It is an evaporator for evaporation or distillation under vacuumconditions. It consists of one or more jacketed heating cylinders and the filmscraping device inside the cylinders with high rotation speed.The film scrapingdevice continuously scrapes the liquid on the wall of the heating cylinder intoa thick and uniform liquid film which moves downward.At the same time, thecomponents with low boiling point rise and evaporate and it will be separated,concentrated, and then discharged from the bottom of the evaporator.
SJM Multi-Effect Falling Film Evaporator
The material liquid is added to the upper part of the heater of the falling filmevaporator through the feeding pump, and after being evenly distributed by the filmdistribution device, it flows evenly downward in the form of liquid film along the innerwall of the heat exchanger tube. The water evaporates Quickly, and the vapor-liquid is fully separated by the separating device.After the secondary steam is condensed,the residualheat can enter the previous system or the following system to continue heating, and the liquid phase is discharged from the separation chamber. This equipment can also be usedin combination with multi-effect, forced circulation, MVR and other evaporators.
The multi-effect evaporation eouipment uses new steam for heating during the single effect. The secondary steamgenerated is reused for the double effect.This step will be repeated for further use of thermal energy. The feed liouidis concentrated during the multi-stage heating and evaporation process,which reduces the operating cost at the same time.
Our company uses the multi-effect energy-saving principles andtechnologies, combined with the membrane pre-treatment in the earlierstep and the drying in the later step, to build the integrated processingeouipment of evaporation. concentration, and solidification. Thecompany has the core technology with independent intellectual propertyrights. We can also provide different treatment methods depending onthe characteristics of the wastewater.
Vacuum Paddle Dryer (Mechanical Seal)
jinling is a professional manufacturer of vacuum paddle dryers. This model is the thrd- generation product designed and upgraded by our company.
Vacuum Paddle Dryer (Packing Seal)
The processing technique called “"six points on one line" is applied, combined with three sets of bearing structure design to improve concentricity and adjustment for thermal expansion
Jinling is a professional manufacturer of vacuum paddle dryers in China. This model has a simple structure. which is adopted from the first generation of domestic products. It is mainly used for the drying or cooling of the powder and granular materials that do not require a sealed environment. The machine is supported by a bearing structure at both ends. Two sets of bearing and Haval bearing seats are used in this case. Packing seal is generally applied. The reducer is side mounted or direct- connected. The design of the mixing shaft and the main body is farly simple.
Jinling is a professional manufacturer of paddle dryer. The paddle dryer with the wedge structure is one of the first traditional dryers in China. It is a low speed mixing dryer that uses heat conduction. The drying barrel is equipped with a jacket. The hollow shaft is equipped with a hollow paddle, wherea heat transfer medium can flow through. The wet material can exchange heat with the barrel and the hot surface of the paddle through the agitation of the mixing paddle, so that the wet material can be dried eventually. Generally, the structure can be horizontal, double shaft or Quadruple shaft.
A variety of structures are designed by our company for the vacuum paddle dryer, which have been applied and produced in large Quantities. The stability, eficiency and strength of the machine has been significantly improved. Speially, the paddle dryer with high vacuum level has acquired the national invention patent;
Our company conducted an independent research on the single screw mixing structure with high vacuum level, and we developed and produced the machine accordingly in 2008
The pressurized spray dryer uses a pressurized atomizer to atomize the solution or the slurry material into fine droplets with the pressure produced by the pressure pump, which significantly increases thesurface area of the material. After the sufficient heat exchange with the hot air, the material can be driedrapidly (between ten seconds and a hundred seconds), so that the products can be powdery or fine particles.
The extract spray dryer is mainly used for drying products with low melting point and high sugar content. It can be equipped with air dehumidifier, automatic cleaning device, air filtration system, cold wall system, windfilm system, exhaust gas treatment system and other devices. The machine has a high level of automation and the operation of this machine is very easy. This machine is generally made of stainless steel and it meets the reQuirements of "GMP".
Spray drying is the simplest way to turn the liuid phase directly to the solid phase. It is mainly used to make powdery and granular products fromsolutions, emulsions, suspensions or pasty liquid materials.
The material is evenly spread on the mesh belt by the feeder. The mesh belt is generally made from 12 -60 mesh stainless steel wire, which is dragged and moved in the dryer by the transmission device.
The blower blows the heated air at the appropriate speed from the bottom of the dryer into the drying chamber along the tangent trajectory for mixing and crushing. The material enters the main body of the machine from the Quantitative feeder.
This machine is applicable for drying materials shaped like filter cakes with relatively high moisture content, such as copolymer of vinyl acetate and vinyl chloride, floc of cellulose acetate fiber, catalyst, CMC, calcined gypsum, electrolytic manganese dioxide, ammonium anthraquinone sulfonate.
The materal is fed into the flash dryer Quantitatively through the feeder. The heated air with high velocity transfers heat Quickly to the powdery material in the drying pipe. The dried material is continuously discharged after being collected by the cyclone separator, and the humid air is discharged through the induced draft fan. The cloth bag dust collector or the water film dust collector can also be added to the machine. Dust explosion should be prevented for fine materials.
Hot-Air Circulating Tray Dryer
jinling Technology is a professional manufacturer of tray dryers, including large size dryers such as the one that is12mX6mX3m.
Markets
Service
Technical Support
Adhere to customer-centric approach and respond quickly to customer needs. Persist in creating long-term value for customers and helping them achieve success.
DO YOU HAVE QUESTIONS?
We will contact you within one working day. Please pay attention to your email.
CONTACT US
Address
501 Changhe Road, Zhenglu Town, Changzhou City, Jiangsu Province, China (ZIP Code: 213115)